Home
Brands
Lubricant FlowLUB 5000, winter grade
  • Lubricant FlowLUB 5000, winter grade

Lubricant FlowLUB 5000, winter grade, 12 btl. box

FL5000WG
Fremco

Special lubricant for fiber cable and micro cable installation. 

Lubrication (FlowLUB) are water based lubricants for all ducts and cables. The lubrication greatly reduces friction and static electricity.

FOR NANOFLOW MAX, MICROFLOW, EASYFLOW SMART and MINIFLOW

Description

Great improvement of blowing length 

It is a water-based product with high lubricating effect. It greatly reduces friction and static electricity. 

Easy to apply

The lubrication spreads evenly on the cable surface/inner wall of the duct. It leaves a very thin film of lubricant and does not make a glue effect.

Low cost

The lubrication is very concentrated, meaning it is very economical to use. 

Winter Grade

Available in a special winter version that can handle temperatures down to -10°C/ 14°F.

PRODUCT USE

Cable and duct prelubrication.

Shake the bottle before use and apply the lubricant in the duct. Place a suitable sponge in the duct and prelubricate the duct with high pressure air.

RECOMMENDED QUANTITY PER 1,000 M:

Duct OD 4 mm - 5 ml = 30 cm full duct

Duct OD 8 mm - 10 ml = 20 cm full duct

Duct OD 12 mm - 15 ml = 15 cm full duct

Sharp turns, loops or long blowing lengths will increase the recommended quantity required.

Product Details
FL5000WG

Data sheet

Aspect
White liquid tiny viscosity
Odour
Characeristic
Viscosity
30 sec. 4 mm Ford cup at 20°C
Gravity
1.030 +/- 0.03 gr/cm3
PH value
7.5 +/- 0.5
Inflammability
Non flammable
Temperature
From 0°C to + 70°C
Biodegradability
Biodegradable
Toxic
Non-toxic
Type of product
Lubrication
Comments (0)
Grade
No customer reviews for the moment.
16 other products in the same category:
Lubricant FlowLUB 5000 Quick view

Reference: FL5000

Brand: Fremco

Lubricant FlowLUB 5000, 12 btl. box

(0)
Special lubricant for fiber cable and micro cable installation.  Lubrication (FlowLUB) are water based lubricants for all ducts and cables. The lubrication greatly reduces friction and static electricity. FOR NANOFLOW MAX, MICROFLOW, EASYFLOW SMART and MINIFLOW
More
Valve for reverse airflow Quick view

Reference: 103-20603

Brand: Fremco

Valve for reverse airflow

(0)
When a fiber/cable must be removed from a microduct due to damage/fault, the valve for reverse airflow is used. It is mounted at the end of the microduct, and when compressed air is connected, the fiber comes out by itself.
More
Blowing tips Quick view

Reference: K02S

Brand: Fremco

Blowing tips

(0)
The fiber blowing tips prevents air getting into the cable that is being blown, avoiding air reaching the cable drum. It provides weight to small fibers, making it easier to fiber blow.
More
Fiberstop end kit Quick view

Reference: 103-20601

Brand: Fremco

Fiberstop end kit

(0)
The fiber stop is a safety system that can be reused to stop the fiber when it arrived at the intended end point. This makes it possible to perform fiber blowing installations with one technician.
More
X-Block Quick view

Reference: 103-10352

Brand: Fremco

X-Block

(0)
The X-block is used for adding one cable to an existing duct with two cables inside. The x-block has a fixed 40 mm connection at one end and in the other end a 50 mm fixed connection.
More
Y-Block Quick view

Reference: 103-201112003

Brand: Fremco

Y-Block

(0)
The flexible Y-block, normally used for overblow, can assist you in adding one cable to an existing duct where another cable is already installed.
More